Wood Pro AVP Chipper/Shredders

  

The Wood-Pro AVP is the only ONE hopper debris handler for everything from leaves & weeds to brush & limbs up to 6 inches in diameter...even stringy vegetation such as palm fronds can be processed with ease.

A Single Feed Hopper For All Kinds Of Vegetation: The AVP's patented processor handles all types of vegetation from leaves, clippings, weeds, and stalks, to 6" diameter branches that require minimal lateral trimming. Entire shrubs and small Christmas Trees are reduced to mulch in a matter of seconds.

The Non-Clogging, Fast Feeding large 30" diameter processor chamber with no sizing rods or screens to block vegetation, discharges processed debris as fast as new material enters the feed hopper. In the AVP, vegetation is reduced to mulch in ONE cycle; there is no slowdown or engine stalling caused by blocked screens or rods; additionally, since the AVP has no feed rollers that slow down the intake, the job gets done in much less time.

Minimal Trimmings Of Laterial Branches: The big hopper and especially the large throat easily accept limbs with lots of side branches and forks. With an AVP, there is no need to waste valuable time pruning side growth from limbs before chipping them.

No Confusion About Hoppers: Compared to twin hopper chipper/shredders, the AVP's single hopper feeding system takes all the guess work out of what size brush or what type vegetation goes into which hopper.

The AVP Is Engineered For Safety From The Start: A circle of safety around the feed hopper is designed to keep the operator at more than arm's length from the cutting mechanism at all times. With the doors of the hopper open, it is very difficult to reach into the hopper from the sides of the AVP.

A Safety Interlock Switch: Prevents starting of the engine when the processor housing is open. All belt shielding meets or exceeds ANSI safety standards, and all PTO models have SAFETY SHEARBOLT YOKES.

Original Split Housing Design: A split processor housing gives instant access to the blades, trident cutter, and flails for inspection of servicing.

  

The Wood Pro AVP has a dynamically balanced processor to help reduce vibration. Units have an idler clutch mechanism to engage the chipper disk/flail knives.

Wood Pro AVP Chipper Prices

• Road Towable Models With Torsion Bar Suspension And Tail Lights (Tail lights optional on model 25Qi160)



• Model 25Qi160: 16hp Briggs and Stratton Vanguard series v-twin engine with OHV (overhead valves), with recoil start



• Fuel capacity is 9 quarts



• The model 25Qi features a manual pulley clutch for more reliable and lower maintenance operation



• Weight is 660 lbs. (shipping weight is 750 lbs.), height is 75 inches, width is 38 inches, length is 70 inches



• Frame is structural steel, trailer is highway towable, 5 bolt highway tires, trailer has heavy duty 1500 lb. torsion bar suspension, 2 inch ball coupler is standard, as an option, a 1 7/8 inch coupler or 2 inch heavy duty cast steel hitch is available



• Tail lights with harness is an option, but available



• Has maximum cutting capacity of 4 inch diameter limbs



• Feed hopper opening is 5 square ft., hopper throat opening is 95 square inches



• Processing chamber diameter is 25 inches, and disk thickness is 4 1/2 inches, unit has 4 chipping blades each 5 inches long, and has 4 twin blade reduction flails with triple fixed cutter



• Hopper now faces towards the back to facilitate feeding the hopper from either side



• All AVP series machines allow you to feed all debris through one hopper with the AVP's non-clog processing system which gives you fast feeding



• Has swivel discharge chute with deflector



• Has bed knife bar with adjuster



• Price model 25Qi160 is $6160.00 delivered (price includes shipping to commercial and residential addresses), shipping weight is 865 lbs., ships by truck



• Model 25Qi160E: Same as above but with electric/recoil starting on the motor - Price is $6195.00 delivered (price includes shipping to commercial and residential addresses), ships by truck



• Model 25Qi180: Same as above except with 18 hp Briggs And Stratton Vanguard engine with recoil start - Price is $6330.00 delivered (price includes shipping to commercial and residential addresses), ships by truck



• Accessories



• Model LK-1: Light kit to make unit highway legal (trailer mounted units are road towable) - Price is $159.95 plus $16.00 UPS shipping (includes installation on chipper) (no extra shipping if ordered with chipper however)



• Model 30Qi22E has a 22 hp, 624cc Kohler engine with electric and recoil start



• Has 30 inch tripple action rotor, 4 - 7 inch chipper knives and 4 twin flails, and a triple fixed cutter



• The unit has a 4 gallon stainless steel fuel tank with fuel gauge



• Power is transmitted using a 4 groove Kevlar Power Band type belt



• This unit has a manual clutch (engaged and released manually with hand lever), manual clutch gives you less maintenance and longer life



• The unit has tail lights standard



• Model 30Qi22E is $9640.00 delivered (price includes shipping to commercial and residential addresses), shipping weight is 1160 lbs.




Tractor PTO Model

PTO Models: Can be operated on-the-go when legs are retracted, or on-the-ground where each leg individually adjusts to uneven or sloping terrain.

Compared to tow or platform units with specific horsepower engines, PTO models can be operated with large hp tractors. The extra horsepower prevents rpm slowdown and the disengaging of the clutch on engine powered units. Shear yokes fully protect the AVP from overloading.





• Model 30QP3: Swivel exhaust chute, 4 groove power band drive, w/1 3/8" quick coupler PTO shaft with safety shear bolt yoke (for tractors with cat. I & II 3 point hitches with 540 rpm pto of 22 to 50 hp, (minimum hp recommended is 22), has 6 inch diameter limb capacity - Price is $6190.00 delivered (price includes shipping to commercial and residential addresses), shipping weight is 1080 lbs. Packaging - 2 heavy wall cartons, palletized.



• Prices with shipping charges include delivery to commerical locations and chippers are palletized. For our overseas customers, these units can be crated for overseas shipment for a cost of $200.00.




Click Here To Expand This To A Full Page Version



We sell directly to the end user.

To Order: Click On The Order Form Button Below For Ordering And Payment Information
Please Order In Writing Only Using Our Order Form.

  

If Our Index Doesnot Appear On The Left Side Of This Page
Then Click On The Home Button Above To See The Many Other Products We Sell


For Sales or Technical Questions, Parts Information, Or To Check On An Order
Please E-Mail us at: sales@wikco.com
All information is on our web site at: www.wikco.com
If you have additional questions, please call us at 520-316-0446 Or Fax us at 520-316-0446




Wikco.com Inc.


Copyright © Wikco.Com Inc., 1997-2009 All Rights Reserved